Cisco Packet Tracer - OSPF Konfigurasi Router (R6, R7)
Selanjutnya kita akan melakukan konfigurasi pada router 6 dan router 7 atau R6, R7, sebelum melakukan konfigurasi pastikan R1-R5 sudah berhasil di konfigurasi dan tidak ada masalah. Untuk R6 dan R7 konfigurasinya masih sama yaitu IP address, perhatikan tabel di bawah ini, sesuaikan IP address yang akan di gunakan serta subnet mask dan interface yang digunakan untuk R6 atau R7.
| Devices | Ip Address | Subnet Mask | Default Gateway |
| R6 | Fa0/0 192.168.8.1/24 | 255.255.255.0 | NA |
| S0/2/0 172.50.1.2/16 | 255.255.0.0 | NA | |
| S0/2/1 172.100.1.1/16 | 255.255.0.0 | NA | |
| S0/0/1 172.60.1.1/16 | 255.255.0.0 | NA | |
| R7 | S0/2/1 172.70.1.2/16 | 255.255.0.0 | NA |
| S0/0/0 172.80.1.2/16 | 255.255.0.0 | NA | |
| S0/0/1 172.90.1.2/16 | 255.255.0.0 | NA | |
| S0/2/0 172.100.1.2/16 | 255.255.0.0 | NA |
Berikut merupakan konfigurasi pada R6
--- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]: no
Press RETURN to get started!
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#host R6
R6(config)#int fa0/0
R6(config-if)#ip add 192.168.8.1 255.255.255.0
R6(config-if)#n sh
R6(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R6(config-if)#ex
R6(config)#int s0/2/0
R6(config-if)#ip add 172.50.1.2 255.255.0.0
R6(config-if)#clock rate 64000
R6(config-if)#n sh
R6(config-if)#
%LINK-5-CHANGED: Interface Serial0/2/0, changed state to up
R6(config-if)#ex
R6(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/0, changed state to up
R6(config)#int s0/2/1
R6(config-if)#ip add 172.100.1.1 255.255.0.0
R6(config-if)#clock rate 64000
R6(config-if)#n sh
%LINK-5-CHANGED: Interface Serial0/2/1, changed state to down
R6(config-if)#
R6(config-if)#ex
R6(config)#int s0/0/1
R6(config-if)#ip add 172.60.1.2 255.255.0.0
R6(config-if)#n sh
R6(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
R6(config-if)#end
R6#
%SYS-5-CONFIG_I: Configured from console by console
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
g%
R6#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R6#wr
Building configuration...
[OK]
R6#
--- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]: no
Press RETURN to get started!
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#host R7
R7(config)#int s0/2/1
R7(config-if)#ip add 172.70.1.2 255.255.0.0
R7(config-if)#clock rate 64000
R7(config-if)#n sh
R7(config-if)#
%LINK-5-CHANGED: Interface Serial0/2/1, changed state to up
R7(config-if)#ex
R7(config)#int
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/1, changed state to u
% Incomplete command.
R7(config)#int s0/0/0
R7(config-if)#ip add 172.80.1.2 255.255.0.0
R7(config-if)#clock rate 64000
R7(config-if)#n sh
R7(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
R7(config-if)#ex
R7(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
R7(config)#int s0/0/1
R7(config-if)#ip add 172.90.1.2 255.255.0.0
R7(config-if)#n sh
R7(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up
R7(config-if)#ex
R7(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up
R7(config)#int s0/2/0
R7(config-if)#ip add 172.100.1.2 255.255.0.0
R7(config-if)#n sh
R7(config-if)#
%LINK-5-CHANGED: Interface Serial0/2/0, changed state to up
R7(config-if)#end
R7#
%SYS-5-CONFIG_I: Configured from console by console
R7#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/0, changed state to up
R7#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R7#wr
Building configuration...
[OK]
Sampai tahap ini, kita telah menyelesaikan konfigurasi pada router 6 dan router 7, selanjutnya kita akan melakukan konfigurasi routing pada masing - masing perangkat router yang sudah kita konfigurasi IP Addressnya. Pastikan tidak ada kesalahan pada setiap konfigurasi sebelumnya.
Cisco Packet Tracer - OSPF Desain Lab dan Menambahkan Perangkat WIC-2T
Cisco Packet Tracer - OSPF Konfigurasi Router (R1,R2, R3)
Cisco Packet Tracer - OSPF Konfigurasi Router (R4, R5)
Cisco Packet Tracer - OSPF Konfigurasi Router (R6, R7)
Cisco Packet Tracer - OSPF Konfigurasi Routing OSPF R1-R7
Cisco Packet Tracer - OSPF Konfigurasi IP Client dan Uji Coba OSPF
0 Response to "Cisco Packet Tracer - OSPF Konfigurasi Router (R6, R7)"
Post a Comment