Cisco Packet Tracer - OSPF Konfigurasi Router (R4, R5)

Berikut ini merupakan konfigurasi lanjutan untuk OSPF yang akan dilakukan pada router R4, dan R5. Sebelum memulai perhatikanlah kembali table IP address yang akan digunakan pada R4 dan R5 serta perhatikan interface, port yang digunakan oleh router 4, router 5 dan subnet mask.

Devices	Ip Address	Subnet Mask	Default Gateway
R4	Fa0/0 192.168.5.1/24	255.255.255.0	NA
	S0/2/0 172.30.1.2/16	255.255.0.0	NA
	S0/0/1 172.90.1.1/16	255.255.0.0	NA
	S0/2/1 172.40.1.1/16	255.255.0.0	NA
R2	Fa0/0 192.168.7.1/24	255.255.255.0	NA
	Fa0/1 192.168.6.1/24	255.255.255.0	NA
	S0/2/1 172.40.1.2/16	255.255.0.0	NA
	S0/2/1 172.50.1.1/16	255.255.0.0	NA

Berikut merupakan konfigurasi pada R4

 --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#host R4
R4(config)#int fa0/0
R4(config-if)#ip add 192.168.5.1 255.255.255.0
R4(config-if)#n sh

R4(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R4(config-if)#ex
R4(config)#int s0/2/0
R4(config-if)#ip add 172.30.1.2 255.255.0.0
R4(config-if)#clock rate 64000
R4(config-if)#n sh

R4(config-if)#
%LINK-5-CHANGED: Interface Serial0/2/0, changed state to up
R4(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/0, changed state to up

R4(config-if)#ex
R4(config)#int s0/0/1
R4(config-if)#ip add 172.90.1.1 255.255.0.0
R4(config-if)#clock rate 64000
R4(config-if)#n sh

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
R4(config-if)#

R4(config-if)#ex
R4(config)#int s0/2/1
R4(config-if)#ip add 172.40.1.1 255.255.0.0
R4(config-if)#n sh

%LINK-5-CHANGED: Interface Serial0/2/1, changed state to down
R4(config-if)#end
R4#
%SYS-5-CONFIG_I: Configured from console by console

R4#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]

Berikut merupakan konfigurasi pada R5

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#host R5
R5(config)#int fa0/0
R5(config-if)#ip add 192.168.7.1 255.255.255.0
R5(config-if)#n sh

R5(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R5(config-if)#int fa0/1
R5(config-if)#ip add 192.168.6.1 255.255.255.0
R5(config-if)#n sh

R5(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

R5(config-if)#ex
R5(config)#int s0/2/1
R5(config-if)#ip add 172.40.1.2 255.255.0.0
R5(config-if)#clock rate 64000
R5(config-if)#n sh

R5(config-if)#
%LINK-5-CHANGED: Interface Serial0/2/1, changed state to up
R5(config-if)#ex
R5(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/1, changed state to up

R5(config)#int s0/2/0
R5(config-if)#ip add 172.50.1.1 255.255.0.0
R5(config-if)#n sh

%LINK-5-CHANGED: Interface Serial0/2/0, changed state to down
R5(config-if)#
R5(config-if)#end
R5#
%SYS-5-CONFIG_I: Configured from console by console

R5#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R5#wr
Building configuration...
[OK]

Okeh pada tahap ini kita sudah berhasil melakukan konfigurasi pada router 4 dan 5, selanjutnya kita lakukan konfigurasi pada router 6 dan 7, silahkan menuju tautan di bawah.

Cisco Packet Tracer - OSPF Desain Lab dan Menambahkan Perangkat WIC-2T

Cisco Packet Tracer - OSPF Konfigurasi Router (R1,R2, R3)

Cisco Packet Tracer - OSPF Konfigurasi Router (R4, R5)

Cisco Packet Tracer - OSPF Konfigurasi Router (R6, R7)

Cisco Packet Tracer - OSPF Konfigurasi Routing OSPF R1-R7

Cisco Packet Tracer - OSPF Konfigurasi IP Client dan Uji Coba OSPF

Share this post