Cisco Packet Tracer - OSPF Konfigurasi Router (R1,R2, R3)

Setelah melakukan persiapan rancangan topologi jaringan yang akan dibuat untuk lab OSPF ini kita akan melakukan konfigurasi ip address telebih dahulu pada R1, R2 dan R3. Silahkan lihat tabel IP Address di bawah untuk setiap perangkat router yang akan di konfigurasi.

Devices	Ip Address	Subnet Mask	Default Gateway
R1	Fa0/0 192.168.1.1/24	255.255.255.0	NA
	S0/0/0 172.10.1.1/16	255.255.0.0	NA
	S0/2/0 172.70.1.1/16	255.255.0.0	NA
	S0/2/1 172.60.1.1/16	255.255.0.0	NA
R2	Fa0/0 192.168.2.1/24	255.255.255.0	NA
	Fa0/1 192.168.3.1/24	255.255.255.0	NA
	S0/0/0 172.10.1.2/16	255.255.0.0	NA
	S0/0/1 172.20.1.1/16	255.255.0.0	NA
R3	Fa0/0 192.168.4.1/24	255.255.255.0	NA
	S0/0/1 172.20.1.2/16	255.255.0.0	NA
	S0/0/0 172.80.1.1/16	255.255.0.0	NA
	S0/2/0 172.30.1.1/16	255.255.0.0	NA

Sebelum memulai konfigurasi pastikan kembali bahwa anda telah mengecek kembali port yang akan dikonfigurasi pada masing – masing perangkat router sudah benar, jika tidak sesuai maka dipastikan network akan mengalami trouble.

Berikut ini merupakan konfigurasi yang dilakukan pada R1

--- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#host R1
R1(config)#int fa0/0
R1(config-if)#ip add 192.168.1.1 255.255.255.0
R1(config-if)#n sh

R1(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R1(config-if)#ex
R1(config)#int s0/0/0
R1(config-if)#ip add 172.10.1.1 255.255.0.0
R1(config-if)#n sh

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
R1(config-if)#ex
R1(config)#int s0/2/0
R1(config-if)#ip add 172.70.1.1 255.255.0.0
R1(config-if)#n sh

%LINK-5-CHANGED: Interface Serial0/2/0, changed state to down

R1(config-if)#ex
R1(config)#int s0/2/1
R1(config-if)#ip add 172.60.1.1 255.255.0.0
R1(config-if)#n sh

%LINK-5-CHANGED: Interface Serial0/2/1, changed state to down
 
R1(config-if)#clock rate 64000
R1(config-if)#end
 
R1#
%SYS-5-CONFIG_I: Configured from console by console

R1#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R1#wr
Building configuration...
[OK]

Berikut ini merupakan konfigurasi yang dilakukan pada R2

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#host R2
R2(config)#int fa0/0
R2(config-if)#ip add 192.168.2.1 255.255.255.0
R2(config-if)#n sh

R2(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R2(config-if)#int fa0/1
R2(config-if)#ip add 192.168.3.1 255.255.255.0
R2(config-if)#n sh

R2(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

R2(config-if)#ex
R2(config)#int s0/0/0
R2(config-if)#ip add 172.10.1.2 255.255.0.0
R2(config-if)#clock rate 64000
R2(config-if)#n sh

R2(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
R2(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up

R2(config-if)#ex
R2(config)#int s0/0/1
R2(config-if)#ip add 172.20.1.1 255.255.0.0
R2(config-if)#n sh

%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
R2(config-if)#end
R2#
%SYS-5-CONFIG_I: Configured from console by console

R2#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R2#wr
Building configuration...
[OK]

Berikut ini merupakan konfigurasi yang dilakukan pada R3

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#host R3
R3(config)#int fa0/0
R3(config-if)#ip add 192.168.4.1 255.255.255.0
R3(config-if)#n sh

R3(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R3(config-if)#ex
R3(config)#int s0/0/1 
R3(config-if)#ip add 172.20.1.2 255.255.0.0
R3(config-if)#clock rate 64000
R3(config-if)#n sh

R3(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to up

R3(config-if)#ex
R3(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to up

R3(config)#int s0/0/0 
R3(config-if)#ip add 172.80.1.1 255.255.0.0
R3(config-if)#n sh

%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
R3(config-if)#ex
R3(config)#int s0/2/0
R3(config-if)#ip add 172.30.1.1 255.255.0.0
R3(config-if)#n sh

%LINK-5-CHANGED: Interface Serial0/2/0, changed state to down
R3(config-if)#end
R3#
%SYS-5-CONFIG_I: Configured from console by console

R3#copy running-config startup-config
Destination filename [startup-config]? 
Building configuration...
[OK]
R3#wr
Building configuration...
[OK]

Jika konfigurasi yang anda lakukan sesuai maka hasil akhir yang anda dapatkan akan sama dengan gambar di atas, lakukan pengecekan kembali pada R1, R2, dan R3 untuk memastikan bahwa konfigurasi telah benar. Selain itu anda dapat mengunduh file latihan OSPF bagian pertama ini pada tautan di bawah atau mengikuti setiap bagian dari artikel OSPF ini melalui tautan yang tersedia.

Cisco Packet Tracer - OSPF Desain Lab dan Menambahkan Perangkat WIC-2T

Cisco Packet Tracer - OSPF Konfigurasi Router (R1,R2, R3)

Cisco Packet Tracer - OSPF Konfigurasi Router (R4, R5)

Cisco Packet Tracer - OSPF Konfigurasi Router (R6, R7)

Cisco Packet Tracer - OSPF Konfigurasi Routing OSPF R1-R7

Cisco Packet Tracer - OSPF Konfigurasi IP Client dan Uji Coba OSPF

Share this post